Liquid R News
Defcon vs STEK PPF: Two Films We Fit and Who Each One Is For
Defcon vs STEK PPF: the short answer
Defcon Glanz and STEK DYNOshield are both clear, self-healing paint protection film made from TPU, and both are around 190 to 203 microns thick. STEK DYNOshield is the pick when the brief is maximum gloss and water beading on bare film. Defcon Glanz is our first recommendation on most cars, because Defcon publishes more of its test data, offers a satin and a 200-colour range on the same warranty system, and its cover moves to the next owner while the e-Warranty record stands.
Liquid R fits both films at our Mitcham workshop, so this is not a case of one good film and one bad one. Every figure below comes from the two makers’ own websites, checked in November 2026.
Thickness and construction
Defcon Glanz is aliphatic TPU at 190 microns, plus or minus 10%, which is about 7.5 mils. The Defcon Glanz product page also gives a single-point puncture resistance of almost 10 kg.
STEK Australia lists DYNOshield at 8 mil, or 203 microns, with a TPU core and a nano-glass top coat, on its DYNOshield page. That 13 micron difference sits inside Defcon’s stated tolerance. On the car you will not see or feel it. We did not find a puncture figure on the STEK pages we read, so on that point there is nothing to compare.
Gloss and water beading
This is where DYNOshield earns its place on our shelf. STEK describes the film as ultra glossy with a super hydrophobic, fluorine-infused top coat, and that matches what we tell customers on our STEK package page: water beads on bare DYNOshield before any coating goes near it.
Defcon Glanz is also a high-gloss film, built to disappear on the paint. If an owner wants the wettest possible look on a dark car and plans to skip a coating over the film, DYNOshield is a fair choice. Most of our jobs leave with a ceramic coating over the film anyway, from $650, and once that is on, the difference in beading narrows.
Self-healing: what each maker publishes
Both films heal light swirls and wash marks with heat from the sun or warm water. Defcon states the depth: its self-healing clear coat is about 13 microns thick, according to the Defcon FAQ. A scratch that stays in that layer closes up. A deeper one stays, and that section of film is replaced.
STEK Australia says minor scratches, swirl marks and light scuffs vanish with simple heat. It does not give a top coat depth on the page we read. In daily use the two behave the same way. The published depth helps when you are deciding whether a mark is worth raising with your installer.
UV and yellowing
Yellowing shows first on white and silver paint. Defcon had Glanz tested by ARPANSA in Melbourne on 15 September 2025: eight specimens, 99.0% of ultraviolet radiation blocked, protection factor 95 (50+), report reference UVR_25-0370-1. The result and the reference sit on the Glanz page.
STEK Australia covers yellowing caused by sun exposure under its DYNOshield warranty. The global STEK DYNO warranty terms are more guarded: yellowing is covered only where STEK determines it, and yellowing from environmental or maintenance factors is excluded. We found no Australian lab report on either STEK site. Defcon is clearer here, and that is the main reason it is our default on white cars.
Warranty: length, registration and resale
Defcon: Glanz and Frozen carry a 10-year limited warranty, Spectra colour film 7 years, and the coming Defcon ONE 12 years, per the Defcon warranty terms. The installer registers the job within 7 days of the invoice in the Defcon e-Warranty system, and cover passes to later owners while that record exists. Nothing extra for the buyer to file.
STEK: the global DYNO terms say 12 years, noting it may vary by region and that maintenance conditions apply. STEK Australia’s DYNOshield page states 10 years for Australian installs, so read 10 years as the local figure. The warranty must be registered on the STEK ONE platform within 30 days of installation, and the owner has to complete an activation step. It is non-transferable unless the new owner sends STEK proof within 30 days of the sale, and then only for the rest of the original term.
So on length STEK can match or beat Defcon Glanz, depending on how the regional terms are applied. On resale, Defcon is simpler. If you sell cars every few years, that matters more than two extra years on paper.
Exclusions both films share
- Stone chips and road debris that go through the film are not a defect under either warranty. The film takes the hit so the paint does not.
- Both makers are wary of third-party products over their film. STEK excludes non-STEK coatings applied after installation. Defcon excludes discolouration caused by third-party coatings, waxes or sealants. Ask your installer which coating goes on top and confirm it is accepted under that film’s terms.
- STEK lists headlamps among areas it does not cover. Defcon’s terms do not mention headlights. If headlight film is part of your quote, ask how it is warranted.
- Washing: Defcon says wait 7 days after fitting, STEK says 48 hours and recommends hand washing. Our aftercare guide uses the longer wait for every film.
Satin and colour
Defcon Frozen is a satin film on the same 190 micron aliphatic TPU build as Glanz, with the same 10 years, per the Defcon Frozen page. STEK lists matte versions in its DYNO clear series as well, and our matte PPF page covers both options.
For a colour change the ranges are very different. Defcon Spectra comes in more than 200 colours in gloss and satin with a 7-year warranty. STEK’s global DYNO page lists eight solid colour films plus chrome and carbon pattern films. We fit colour transformation in Spectra, from $6980 for a full car.
Which one should you choose?
Choose STEK DYNOshield if gloss and bare-film beading are what you care about most, you plan to keep the car, and you are happy to complete STEK’s owner activation. Choose Defcon Glanz if you want published UV test data, a warranty that goes with the car at sale, or a matching satin or colour film from the same maker.
Either way, the fit decides how it looks in year five: edges, seams and paint prep. At Liquid R, paint protection film starts at $180 for headlights, a wear and tear pack is from $380, a full front is from $1980 and every painted panel is from $5980, quoted as a fixed price before you book. Many owners add window tinting or a detailing package at the same visit, and a Tesla or other EV gets the same choice of film.
Questions owners ask
Is Defcon PPF as good as STEK?
On published figures, yes. Glanz is 190 microns against DYNOshield’s 8 mil, both self-heal with heat, and both carry 10 years on clear film in Australia. Defcon adds an ARPANSA UV test and a transferable warranty. STEK’s edge is gloss and beading straight off the roll.
Does Liquid R install STEK?
Yes. We fit STEK DYNOshield and Defcon Films Australia paint protection film at Cook Road in Mitcham, Melbourne, and we will tell you which suits your car rather than pushing one brand.
Is the STEK warranty 10 or 12 years in Australia?
STEK’s global terms say 12 years and note that it varies by region. STEK Australia’s DYNOshield page says 10 years for Australian installs. Ask your installer to show you the warranty document that will be registered for your car.
Does the PPF warranty transfer when I sell the car?
Defcon’s does while the e-Warranty record exists. STEK’s is non-transferable unless the new owner sends STEK proof within 30 days of buying the car, and cover then runs only to the end of the original term.
Can I put ceramic coating over STEK or Defcon film?
Yes, and most of our customers do. Both makers restrict third-party products over their film, so confirm the coating your installer uses is accepted under that film’s warranty before it goes on.
Related Guides
Contact Us
Get in touch with us or stop on by to say hey
Give us a call or drop by anytime:
P: 1800 985 880
E: info@liquidr.com.au
A: 12/23A Cook Road Mitcham VIC 3132
Opening hours:
Monday to Friday 8:30am-5:00pm
Saturday 8:30am-12:30pm